Flanges

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. It''''s a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard:ASTM A105, ASTM A182
Material Carbon Steel, Alloy Steel, Stainless Steel
Size 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Special made outer diameters: Up to 60.
Class range: Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type: RF (Raised Face), RTJ (Ring Type Joint)

 

 

Additional Information:

• Production Capacity: 150# , 300# , 400# , 600# , 900# , 1500# , 2500#
• Delivery Time: Ready Stock
• Packaging Details: Export Sea worthy Packing, protected with end caps on both side. Full pipe covered with plastic

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material Carbon Steel, Alloy Steel, Stainless Steel
Size1/2 to 24, customized up to 60
Pressure RatingsClass 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1/2, 2,  3, 4, 6, 8, 10, 12, to 24.
Special made outer diameters: Up to 60.
Class range: Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type: RF (Raised Face), RTJ (Ring Type Joint)

 

Export Sea worthy Packing.

Bhagyalaxmi Industrial

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material Carbon Steel, Alloy Steel, Stainless Steel
Size: 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1/2, 2,  3, 4, 6, 8, 10, 12, to 24.
Special made outer diameters Up to 60.
Class range Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type RF (Raised Face), RTJ (Ring Type Joint)

 

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. It''s a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

 

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Class range: Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type: RF (Raised Face), RTJ (Ring Type Joint)

 

 

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. It's a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

 

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Special made outer diameters: Up to 60.
Class range: Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type: RF (Raised Face), RTJ (Ring Type Joint)

 

 

 

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material Carbon Steel, Alloy Steel, Stainless Steel
Size 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1/2, 2,  3, 4, 6, 8, 10, 12, to 24.
Special made outer diameters: Up to 60.
Class range Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type RF (Raised Face), RTJ (Ring Type Joint)

 

 

Bhagyalaxmi Industrial

 

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

Hastelloy Lap Joint Flanges

Titanium Lap Joint Flanges

Duplex Stainless steel Lap Joint Flanges

 321/321H Lap Joint Flanges

 454/454L Lap Joint Flanges

317/317L Lap Joint Flanges

316/316L Lap Joint Flanges

 304/304L Lap Joint Flanges

 Inconel  Lap Joint Flanges

 Monel Lap Joint Flanges

A105 Carbon steel Lap Joint Flanges

A234 carbon steel Lap Joint Flanges

High quality Lap Joint Flanges

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld)

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material  Carbon Steel, Alloy Steel, Stainless Steel
Size 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1/2, 2,  3, 4, 6, 8, 10, 12, to 24.
Special made outer diameters Up to 60.
Class range Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type: RF (Raised Face), RTJ (Ring Type Joint)

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

Stainless Steel SS316 SORF Flanges
Stainless Steel SS304 SORF Flanges
Stainless Steel SS316 BLRF Flanges
Stainless Steel SS304 BLRF Flanges
Stainless Steel SS316 SORF Flanges With Collar and Hub
Stainless Steel SS316 SORF Flanges Without Collar and Hub

Product Details:

 Hastelloy Flanges

Titanium Flanges

Duplex Stainless steel Flanges

 321/321H Flanges

 904/904L Flanges

317/317L Flanges

316/316L Flanges

 304/304L Flanges

 Inconel Flanges

 Monel Flanges
Aluminium Flanges

Carbon Steel A105 Flanges

Carbon Steel A234 WPB Flanges

Aluminium Flanges

SS304 Flanges

SS304L Flanges

SS304H Flanges

SS309S Flanges

SS316 Flanges

SS316L Flanges

SS316H Flanges

SS310 Flanges

SS310S Flanges

SS317 Flanges

SS317L Flanges

SS321 Flanges

SS321H Flanges

SS347 Flanges

SS409 Flanges

SS410 Flanges

SS420 Flanges

SS430 Flanges

SS444 Flanges

SS904L Flanges

253MA Flanges

Duplex 2205 Flanges

Duplex 2507 Flanges

Titanium GR. 2 Flanges

Titanium GR. 5 Flanges

Titanium GR. 7
Flanges

Hastelloy C22 Flanges

Hastelloy C276 Flanges

Nickel Flanges

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready Stock
• Packaging Details: Export Sea worthy Packing

Product Details:

150 300  400  600  900  1500  2500 

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld Buttweld.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

 

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Grade 304 chrome steel is a general "18/eight", austenitic grade stainless steel. Grade 304 SS is one of the maximum versatile and maximum broadly utilized stainless steel grades.  take a look at out the chrome steel flange price listing India. a number of the most essential residences of the 304 grade stainless steel is its excellent forming and welding characteristics.

See SS Flange charge listing India

The balanced austenitic micro structure segment of Grade 304 allows it to be significantly deep drawn with out intermediate annealing. Grade 304 stainless steel is willingly braked or roll-formed into a ramification of components. as a result, it is able to be used for packages within the commercial, architectural, and transportation fields. even though 304 grade stainless-steel has great welding.traits, put up-weld annealing treatment is not required even as welding skinny sections. To research extra approximately the ss 304 flange charge listing, click here. Fittings like flanges crafted from grade 304 SS have good forming in addition to weld in a position houses. check out the chrome steel flanges fee list.

Grade 316 is the usual molybdenum-bearing grade stainless steel most effective second in significance to 304 among the austenitic stainless steels grades. discover extra approximately grade 316 ss flange charge list India.  This molybdenum based gives 316 grade better overall corrosion resistant properties as compared to Grade 304. research more approximately the ss 316 flange fee. Grade 316 is particularly recognised for its better resistance to pitting and crevice corrosion in chloride environments. 316 SS has first rate forming and welding traits. See the stainless-steel puddle flange fee. it's miles conveniently brake or roll fashioned into a ramification of parts for packages in the industrial, architectural, and transportation fields. much like 304ss, Grade 316 additionally has first-rate welding traits. put up-weld annealing isn't required for 316SS while welding thin sections. See extra approximately the stainless steel flange cost.

The blind flange is a clean disc with holes for bolts. Blind flanges are frequently used in aggregate with another type of flange, considering the fact that blind flanges are commonly used as a way of isolating the piping machine.  Or a blind flange may also be used to terminate the piping as an cease. any other software of a Blind flanges is that it could also be used as a manhole cowl inside the vessel. discover extra approximately stainless steel blind flange costs.

conventional Pipe flanges are to be had in a couple of kind, as an instance, they are available inside the diverse bureaucracy like – threaded, welding neck, blind, lap joint, socket weld, and so forth.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150 300 400 600 900 1500 2500

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld Buttweld.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES , SERIES A , SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. (A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping). Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face (RF) or flat faced (FF). If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Blinde flens , Flange cego , Vak karima , Flan???? oarb?? ,  Blind flans ,  , Tutup katup , Flange na nDall , Flangia cieca ,  Brida ciega , Slep p??ruba , Blindflns ,  Kr Flan?? , , Blindflansch ,, , Zalepka , Mt bch m , Blann Flange , Brida ciega , 

 

Additional Information:

• Production Capacity: 10000 Tonnes
• Delivery Time: Ready Stock
• Packaging Details: Export Sea worthy Packing.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES , SERIES A , SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. (A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping). Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face (RF) or flat faced (FF). If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

 

Export Sea worthy Packing.

Bhagyalaxmi Industrial

Additional Information:

• Delivery Time: Ready Stock
• Packaging Details: Export Sea worthy Packing.

Product Details:

Stainless Steel Socketweld Flange
Carbon Steel Socketweld Flange
Nickel Alloy Steel Socketweld Flange

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150 300 400  600 900  1500 2500

Inconel Blind Flange 150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

 Inconel Blind Flange ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES , SERIES A , SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. (A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping). Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Inconel Blind Flange Inconel Blind Flange

Export Sea worthy Packing.

Bhagyalaxmi Industrial

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy Packing.

Product Details:

150 300 400  600 900 1500 2500

150 Class  300 Class 400 Class 600 Class 900 Class 1500 Class  2500 Class

ASTM A182 ANSI B16.5  ASME B 16.5  ANSI B 16.47 DIN FLANGES  BS TABLE FLANGES  SERIES A  SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material Carbon Steel, Alloy Steel, Stainless Steel
Size 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1/2, 2,  3, 4, 6, 8, 10, 12, to 24.
Special made outer diameters: Up to 60.
Class range Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type RF (Raised Face), RTJ (Ring Type Joint)

 

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150 300 400  600 900 1500  2500

150 Class  300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Class

ASTM A182 ANSI B16.5  ASME B 16.5  ANSI B 16.47 DIN FLANGES  BS TABLE FLANGES  SERIES A  SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready Stock
• Packaging Details: Export sea worthy packing

Product Details:

150 300  400 600  900  1500  2500

150 Class  300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Class

ASTM A182 ANSI B16.5  ASME B 16.5  ANSI B 16.47 DIN FLANGES  BS TABLE FLANGES  SERIES A  SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used.A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact during construction of a pipeline a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

We are Dealing in Blind Flanges.
The blind flange is a blank disc with holes for bolts. Blind flanges are often used in combination with another kind of flange, since blind flanges are mostly used as a means of isolating the piping system.  Or a blind flange could also be used to terminate the piping as an end. Another application of a Blind flanges is that it could also be used as a manhole cover in the vessel.

Product Details:

150 300 400 600  900 1500  2500

150 Class  300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material Carbon Steel Alloy Steel, Stainless Steel
Size 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. Alloy for F11, F22, stainless for F304 F304L, F316 F316L
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1 2, 2,  3, 4, 6, 8 10, 12 to 24
Special made outer diameters: Up to 60
Class range Class 150, Class 300, 400, 600, 900, 1500, 2500 or LB. PN 2.5 to PN 250.
Flange face type: RF Raised Face, RTJ Ring Type Joint

 

Bridas    flange  Flansch  reborde refuerzo pestanapatin, brida , lauma, reunus, laippa, richel, flens,  mesa , labi , Flanges, Deslizarse en la brida , Glip op flens , Deslizamento na flange, Csusztassa a karimat , Alunecare pe flan  Selipkan Flange , Duillin Ar Flange , 

Deslizarse en la brida , Klizanje na prirubnici , Slip On Flens ,   Flansch aufstecken ,   Flip On Flange

 

Export Sea worthy Packing.

Bhagyalaxmi Industrial

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready Stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

 

A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

This flange type will be welded to a pipe or fitting with a single full penetration, V weld (Buttweld).

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

We are Dealing in Threaded Flanges

We “Bhagyalaxmi Industrial”  are one of the leading Exporters & Manufacturers  of Pipes, Flanges. Pipe fittings , Rods, Sheets, Plates, Coils, Fasteners , etc. Specialist in material like Stainless Steel , Carbon Steel, high Nickel Alloys.

Product Details:

Stainless Steel Pipe Flange.
slip on flange with raised face (sorf flange), sorf flange dimension from 1/2 inch to 96 inch, pressure rating from 150lb/sq.in to 2500lb/sq.in, we usually offer ANSI/ASME/DIN etc. Standard Flange with sorf flange dimension. 150lb Slip On Flange with raised face from 1/2 inch to 24 inch of B16.5

Product Details:

We are Dealing in Stainless Steel 304 Flange.
S 304 plate flange are some of the most widely used flanges of all. Dinesh Industries is a manufacturer and supplier of 304 grade stainless steel materials including flanges. We offer a wide range of flanges in this grade and in different types as well. Our Stainless Steel 304 Flangesis a metallic ring that is used to add to the attachment surface at the end of a pipe. Since the 304 material is strong and has an extent of corrosion resistance, it is suitable for more general service applications. Also, the pricing is very cheaper, these are used widely. Manufacturer of SA182 F304 Flanges in Mumbai. The a182 is a specification for fittings in the 304, 304L and 304H grades of steels.

Product Details:

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready Stock
• Packaging Details: Export Sea worthy Packing

Product Details:

150 300 400 600  900  1500  2500

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASTM A182, ANSI B16.5 , ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES , SERIES A , SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASTM A182, ANSI B16.5 , ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES , SERIES A , SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used. (A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping). Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face (RF) or flat faced (FF). If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Export Sea worthy packing

Product Details:

150# , 300# , 400# , 600# , 900# , 1500# , 2500#

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES

Slip on Flange is essentially a ring that is placed over the pipe end, with the flange face extending from the end of the pipe by enough distance to apply a weld bead on the inside diameter. The OD of slip on flange is also welded on the back side of the flange.

Slip on flange, also called SO flange. Its a kind of flange slides over the pipe with internal design is slightly larger than the pipe. Since the inner diameter of the flange is slightly larger than the outer diameter of the pipe, the SO flange can be directly connected to equipment or pipe by fillet weld at the top and bottom of the flange. It is used to insert the pipe into the inner hole of the flange.

Standard ASTM A105, ASTM A182
Material Carbon Steel, Alloy Steel, Stainless Steel
Size 1/2 to 24, customized up to 60
Pressure Ratings Class 150 to Class 2500
Face Type RF, RTJ

Raised Face Slip On Flange

There is a small portion extruded from the bottom face of the slip on flange, this type is raised face slip on flange. The function of this area is to place a gasket seat during installation to get a better sealing performance. 

As the pressure ratings bigger, the height of this raised face will be bigger.

RTJ Slip on Flange

A small grooved is machined on the raised face part, this form is called RTJ type, the function of this groove is to place the gasket ring, also applied for sealing, compared to RF type, RTJ is designed for high pressure use.

ASTM A105 for carbon steel slip on pipe flanges.
ASTM A182 for alloy and stainless slip on flanges. (Alloy for F11, F22, stainless for F304/F304L, F316/F316L)
ASME B16.5 for pipe flanges and flanged fittings.
BS 3293
DIN 86029

 

Common outer diameters: 1/2, 2,  3, 4, 6, 8, 10, 12, to 24.
Special made outer diameters: Up to 60.
Class range Class 150, Class 300, 400, 600, 900, 1500, 2500(# or LB). PN 2.5 to PN 250.
Flange face type: RF (Raised Face), RTJ (Ring Type Joint)

 

Additional Information:

• Packaging Details: Export Sea worthy Packing.

Product Details:

150 300 400 600 900 1500 2500

150 Class , 300 Class, 400 Class, 600 Class, 900 Class, 1500 Class, 2500 Class

ASTM A182, ANSI B16.5 , ASME B 16.5 , ANSI B 16.47 , DIN FLANGES , BS TABLE FLANGES , SERIES A , SERIES B

A blind flange is a solid flange. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used.A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping. Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank. The best practice is to use a standard gasket for these blinds. Blind flanges, just like standard pipe flanges, can be raised face RF or flat faced FF. If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test. If it is FF we would TYPICALLY use a full face gasket, because the most common reason the flange is FF is that it is not designed to handle the bending forces that result when using a ring gasket or a RF flange against the FF flange. Again, we treat a blind flange just like any other pipe flange.

Blind flanges are commonly used in petrochemical, pipe engineering, public services and water works.

A blind flange is useful for making repairs to a pipeline further up the line. In fact, during construction of a pipeline, a blind flange may be built into the final length of pipe. This allows for expansion or continuation of the pipeline simply by adding onto the final flange.

Without a blind flange, it would be next to impossible to repair or perform ongoing maintenance to a pipeline unless the flow was shut off at a earlier valve, which could affect miles of pipeline.

The use of flanged pipe has significantly sped up the process for constructing pipelines. It has also made the task of repair and sectional replacement easier. Sections of pipe can now be assembled anywhere in the world and shipped to the job site. Once there, they can simply be bolted in place and the repair is done.